COMPLETE TAPE APPLICATION MACHINE
EPackPro.
Fully automatic, stand-alone line for corrugated packaging. In a single pass it applies 2 hotmelt glue lines, covers them with silicone tape and adds a tear tape — a ready peel-and-seal closure with an easy-open strip.
EPACKPRO / MACHINE OVERVIEWFROM INFEED TO DELIVERY
Four sections.
One integrated process.
Four servo-driven modules form one continuous line. It runs stand-alone or, after a technical check, can be linked with existing folder-gluers.

Servo feeder with vacuum belts and adjustable feeding gates for reliable sheet separation.
- 7 feeding belts (45 mm) with angle adjustment
- Vacuum belts for easier feeding
- 2 feeding gates with angle adjustment
- 600 mm belt length, 700 mm side lays
- Tool carrier expandable up to 900 mm; table for long boxes
Servo-positioned left and right alignment belts square every blank before application.
- Left and right alignment module, 50 mm belts
- 2,000 mm alignment length
- Servo-driven linear movement
- Independent adjustment of each roller
- Bottom support bars for wide and long boards
2 hotmelt glue lines, each covered by silicone tape (STM), plus 1 tear tape (RTM).
- 2,200 mm section length, servo driven
- Driven top track with belts
- Additional belt drive for the tear tape applicator
- Hotmelt system: 50 kg tank, 40 kg/h, 2 slot guns for coatings up to 90 mm wide
- Jumbo unwinder for silicone and tear tape: rolls up to 500 mm (152 mm core), automatic speed regulation
- Open design for easy access and setup
3.5 m servo conveyor with counter, UV marker and sorting stop for long boards.
- 3.5 m belt conveyor, 1,650 mm wide
- Servo driven, independent speed setting
- Start–stop function and counter
- UV water marker
- Stop system with 2 pneumatic cylinders for sorting long boards
- Mounted on wheels
Touch-screen HMI with PLC motion control; tape length, position and speed are set per job.
- Recipes for quick job changeover
- 4 IP cameras — one per station
- 32" overview screen for production
- Safety light barriers and E-stop on each segment
EPACKPRO IN OPERATION
See the process in action.
Watch the EPackPro machine applying tape to packaging.
EPackPro in operation · approximately 47 seconds.
MACHINE CLOSE-UP
A closer look at the machine.
Controls, infeed and installed applicators. Select a photo to enlarge it.
TECHNICAL DATA / EPACKPRO 165
EPackPro 165
at a glance.
Values for the standard configuration. The final configuration is confirmed in your quotation, based on your packaging format and tape type.
Send your product requirements ↗| Performance | |
|---|---|
| Line speed | 20–250 m/min |
| Capacity (STM) | up to 30,000 pcs/h* |
| Cardboard width | 200–1,650 mm |
| Tape segments per blank | up to 5 |
| Machine | |
| Construction | 15 / 25 mm steel |
| Overall length | approx. 6,500 mm |
| Weight | approx. 4,500 kg |
| Standard configuration | 2 × hotmelt, 2 × STM, 1 × RTM |
| Integration with folder-gluers | optional after technical check |
| Utilities | |
| Power supply | 230 / 400 V, 50 A |
| Installed power | 14.8 kW |
| Compressed air | min. 6 bar |
| Safety and control | |
| Safety | light barriers, E-stop per segment |
| Monitoring | 4 IP cameras, 32" screen |
| Certification | CE |
The EPackPro range
Choose the working width that matches your board sizes.
* Values depend on packaging format, tape configuration and operating conditions. Specifications may change without notice; the final configuration is confirmed in the quotation.
YOUR CONFIGURATION
One integrated machine.
Your choice of applicators.
Compare STM and RTM specifications and contact us to discuss the right combination.
Explore applicators ↗
Configuration illustration. The scope of delivery is specified in your quotation.

DISCUSS YOUR PROJECT
Contact